Swaged fittings must be hydraulically crimped to the cable. The fittings themselves, being technically simple, are more reliable and less expensive than swageless fittings.
This fitting is identical to the Adjust-a-Body® with Hanger Bolt except the extended length hanger bolt is 3” long. Designed to reach past sleeves and drywall to find the wood post or frame underneath. It is used for sleeved posts with an outside diameter of greater than 4-1/2”.
Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must be purchased separately.
| Cable Diameter | Part No. | Use With Ferrule No. |
|---|---|---|
| 1/8” |
A-JB6-L |
F-4 |
| 3/16” | F-6 |
For sleeved posts with an outside diameter of greater than 4-1/2”, use the extended length lag eye. The extended length lag is 3” long, designed to reach past sleeves and drywall to find the wood post or frame underneath.
Extended lag eye and screw sold separately.
Type 316 Stainless Steel
| Cable Diameter | Part No. | Use Ferrule No. | Use With Screw No. | Use With Extended Length Lag Eye | “E” Thread | “A” | “B” | “S” | “T” Thread | “Lt” | “Ln” | “Lr” | “D” Dia. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1/8” | A-JTE6 | F-4 | SC-6 | LE-6L | 1/4-28 | .233″/.229″ | .500″ | .44″ | 5/16-24 LH | 2.00″ | .375″ | 2.75″ | .490″ |
| 3/16” | A-JTE6 | F-6 | SC-6 | LE-6L | 1/4-28 | .233″/.229″ | .500″ | .44″ | 5/16-24 LH | 2.00″ | .375″ | 2.75″ | .490″ |
The Adjust-A-Body® with Threaded Bolt is an exposed, swaged, tensioning, face-of-the-post-mounted fitting that is recommended for level runs only. This fitting is available for 1/8”, 3/16”, 1/4”, 5/16”, and 3/8” diameter 1×19 stainless steel cable.
The Adjust-A-Body® with Threaded Bolt can be used with any fitting on the opposite end of the run. The short thread of the threaded bolt portion of the fitting is secured into a pre-drilled and tapped hole in the end post. The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed all the way onto the threaded bolt first, followed by the body, which is secured onto the threaded bolt, creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to secure the fitting from loosening.
Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must be purchased separately.
Type 316 Stainless Steel
| Cable Diameter | Part No. |
Use with Ferrule No. |
“S” | “T” Thread | “Ls” | “Lt” | “Loq” | “Ln” | “Lr” | “D” |
|---|---|---|---|---|---|---|---|---|---|---|
| 1/8” | A-JTB6 | F-4 | 5/16-24 | 5/16-24 L.H. | .375″ | 2.00″ | 2.625″ | .375″ | 2.75″ | .490″ |
| 3/16” | F-6 | |||||||||
| 1/4” | A-JTB8 | F-8 | 5/16-24 | 7/16-20 L.H. | .375” | 2.50″ | 3.125″ | .500″ | 3.00″ | .617″ |
| 5/16” | A-JTB12 | F-10 | 1/2-20 | 9/16-18 | .62″ | 3.00″ | 4.00″ | .62″ | 4.50″ | .744″ |
| 3/8” | F-12 |
The Adjust-A-Body® with Threaded Eye fitting is an exposed, swaged, tensioning, face-of-the-post-mounted fitting that can be used on level or pitched runs. This fitting is available for 1/8”, 3/16”, and 1/4” diameter 1×19 stainless steel cable.
The Adjust-A-Body® with Threaded Eye can be used with any fitting on the opposite end of the run. This fitting attaches to the end post by installing a Threaded Tab into a pre-drilled and tapped hole in the end post and attaching the threaded eye portion of the fitting to the threaded tab with a button head screw. The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed all the way onto the threaded eye first, followed by the body, which is secured onto the eye, creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to secure the fitting from loosening.
While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the threaded eye portion of the fitting pivots at the tab.
Use of this fitting requires that an appropriately sized ferrule is swaged onto the cable. Ferrule sold separately.
| Cable Diameter | Part No. | Use with Ferrule No. | Use with Screw No. | Use with Tab No. | “E” Thread | “A” | “B” | “S” | “T” Thread | “Lt” | “Ln” | “Lr” | “D” Dia. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1/8” | A-JTE6 | F-4 | SC-6 | TT-6B | 1/4-28 | .233″/.229″ | .500″ | .44″ | 5/16-24 LH | 2.00″ | .375″ | 2.75″ | .490″ |
| 3/16” | A-JTE6 | F-6 | SC-6 | TT-6B | 1/4-28 | .233″/.229″ | .500″ | .44″ | 5/16-24 LH | 2.00″ | .375″ | 2.75″ | .490″ |
| 1/4” | A-JTE8 | F-8 | SC-8 | TT-8B | 3/8-24 | .295″/.285″ | .874″ | .68″ | 7/16-20 LH | 2.50″ | .500″ | 3.00″ | .617″ |
The Adjust-A-Body® with Threaded Eye is a swaged, tensioning, face-of-the-post-mounted fitting that can be used on level or pitched runs. This fitting is available for 1/8”, 3/16”, and 1/4” diameter 1×19 stainless steel cable.
The Adjust-A-Body® with Threaded Eye can be used with any fitting on the opposite end of the run. This fitting attaches to the wood end post by installing a Lag Eye into a pre-drilled hole in the end post and attaching the threaded eye portion of the fitting to the lag eye with a button head screw. The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed all the way onto the threaded eye first, followed by the body, which is secured onto the eye, creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to prevent the fitting from loosening.
While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the threaded eye portion of the fitting pivots at the lag eye. The pre-drilled hole for the lag eye is drilled level, making installation easy.
Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must also be purchased separately.
Type 316 Stainless Steel
| Cable Diameter | Part No. | Use with Ferrule No. | Use with Screw No. | Use with Lag Eye No. | “E” Thread | “A” | “B” | “S” | “T” Thread | “Lt” | “Ln” | “Lr” | “D” Dia. |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1/8” | A- JTE6 | F-4 | SC-6 | LE-6 | 1/4-28 | .233″/.229″ | .500″ | .44″ | 5/16-24 LH | 2.00″ | .375″ | 2.75″ | .490″ |
| 3/16” | A-JTE6 | F-6 | SC-6 | LE-6 | 1/4-28 | .233″/.229″ | .500″ | .44″ | 5/16-24 LH | 2.00″ | .375″ | 2.75″ | .490″ |
| 1/4” | A-JTE8 | F-8 | SC-8 | LE-8 | 3/8-24 | .295″/.285″ | .844″ | .875″ | 7/16-20 LH | 2.50″ | .500″ | 3.00″ | .617″ |
The Adjust-A-Body® with Concrete Anchor Bolt is an exposed, swaged, tensioning, face-of-the-surface-mounted fitting that is recommended for level runs terminating at a concrete surface only. This fitting is available for 1/8”, 3/16”, and 1/4” diameter 1×19 stainless steel cable.
The Adjust-A-Body® with Concrete Anchor Bolt can be used with any fitting on the opposite end of the run. A concrete anchor is driven into a pre-drilled hole in the concrete surface. The short thread of the anchor bolt portion of the fitting is threaded into the concrete anchor. The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed all the way onto the exposed machine thread of the anchor bolt, followed by the body, which is secured onto the anchor bolt until effectively creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to prevent the fitting from loosening.
Use of this fitting requires that an appropriately sized ferrule is swaged onto the cable. Ferrule sold separately, see information on page 8. The Red Head® Concrete Anchor is available for purchase at many building supply retailers and distributors throughout the country.
| Cable Diameter | Tube Length | Part No. |
|---|---|---|
| 1/8”, 3/16” | 3/4” | CS-TUBE |
| 1/8”, 3/16” | 3/4” | CS-TUBE |
| 1/8”, 3/16” | 3/4” | CS-TUBE |
| 1/8”, 3/16” | 3/4” | CS-TUBE |
| 1/8”, 3/16” | 3/4” | CS-TUBE |
| Cable Diameter | Part No. | Use with Ferrule No. | “S” | “T” Thread | “Ls” | “Lt” | “Loq” | “Ln” | “Lr” | “D” |
Use with “Red Head” Brand Concrete Anchor Carbon Steel |
Use with “Red Head” Brand Concrete Anchor Stainless |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1/8” | A-JAB6 | F-4 | 3/8-16 | 5/16-24 L.H. | .500″ | 2.313″ | 3.188″ | .375″ | 2.75″ | .490″ | RM-38 | SRM-38 |
| 3/16” | A-JAB6 | F-6 | ||||||||||
| 1/4” | A-JAB8 | F-8 | 1/2-13 | 7/16-20 L.H. | 1.125″ | 2.500″ | 3.938″ | .500″ | 3.00″ | .617″ | RM-12 | SRM-12 |
Exposed, swaged, tensioning, face-of-the-post-mounted fitting suitable for level or pitched runs and is available for 1/8˝ and 3/16˝ diameter 1×19 stainless steel cable.
Part Number: A-J6-CL-C
| Cable Diameter | Use with Ferrule No. | “T” Thread | “Lt” | “Ln” | “Lr” | “D” Dia. |
|---|---|---|---|---|---|---|
| 1/8” | F-4 | 6/16-24 LH | 2.00″ | .375″ | 2.73″ | .490″ |
| 3/16” | F-6 |
The Adjust-A-Body® with Hanger Bolt is a swaged, tensioning, face-of-the-post-mounted fitting that is recommended for level runs only. This fitting is available for 1/8”, 3/16”, and 1/4” diameter 1×19 stainless steel cable.
The Adjust-A-Body® with Hanger Bolt can be used with any fitting on the opposite end of the run. The lag thread of the hanger bolt portion of the fitting is driven into a pre-drilled hole in the wood end post. The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed onto the hanger bolt first, followed by the body, which is secured onto the hanger bolt, creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to prevent the fitting from loosening.
We do not recommend this fitting being installed in pitched applications because it would require drilling all of the holes in the end post at an angle. While this is possible with special fixtures, if it is not done correctly the end result would be visually unacceptable.
Use of this fitting requires an appropriately sized ferrule swaged onto the cable, which must be purchased separately.
TYPE 316 STAINLESS STEEL
| Cable Diameter | Part No. | Use With Ferrule No. | “S” | “T” Thread | “Ls” | “Lt” | “Ln” | “Lr” | “D” Dia. | Minimum Timber Size |
|---|---|---|---|---|---|---|---|---|---|---|
| 1/8” | A-JB6 | F-4 | 5/16” | 5/16-24 LH | 1.50″ | 2.00″ | .375″ | 2.75″ | .490″ | 4 X 4 |
| 3/16″ | A-JB6 | F-6 | 5/16” | 5/16-24 LH | 1.50″ | 2.00″ | .375″ | 2.75″ | .490″ | 4 X 4 |
| 1/4″ | A-JB8 | F-8 | 7/16” | 7/16-20 LH | 2.00″ | 2.50″ | .500″ | 3.00″ | .617″ | 4 X 4 |
Exposed, swaged, tensioning, face-of-the-post-mounted fitting suitable for level or pitched runs and is available for 1/8˝ and 3/16˝ diameter 1×19 stainless steel cable.
Part Number: A-J6-CL-W
| Cable Diameter | Use with Ferrule No. | “T” Thread | “Lt” | “Ln” | “Lr” | “D” Dia. |
|---|---|---|---|---|---|---|
| 1/8” | F-4 | 6/16-24 LH | 2.00″ | .375″ | 2.73″ | .490″ |
| 3/16” | F-6 |
Exposed, swaged, tensioning, face-of-the-post-mounted fitting suitable for level or pitched runs and is available for 1/8˝ and 3/16˝ diameter 1×19 stainless steel cable.
| Cable Diameter | Use with Ferrule No. | “T” Thread | “Lt” | “Ln” | “Lr” | “D” Dia. |
|---|---|---|---|---|---|---|
| 1/8” | F-4 | 6/16-24 LH | 2.00″ | .375″ | 2.73″ | .490″ |
| 3/16” | F-6 |
The Adjust-A-Jaw® is a swaged, tensioning, face-of-the-post-mounted fitting that can be used on level or pitched runs. This fitting is available for 1/8”, 3/16”, 1/4”, 5/16”, and 3/8” diameter 1×19 stainless steel cable.
The Adjust-A-Jaw® can be used with any fitting on the opposite end of the run. This fitting attaches to the wood end post by installing a Lag Eye into a pre-drilled hole in the end post and attaching the threaded jaw portion of the fitting to the lag eye with a button head screw (see information at bottom of page). The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed all the way onto the threaded jaw first, followed by the body, which is secured onto the jaw, creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to prevent the fitting from loosening.
While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the threaded jaw portion of the fitting pivots at the lag eye. The post hole for the lag eye is drilled level, making installation easy.
Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must be purchased separately .
For sleeved posts with an outside diameter of greater than 4-1/2”, use the extended length lag eye. The extended length lag is 3” long, designed to reach past sleeves and drywall to find the wood post or frame underneath. Extended lag eye and screw sold separately.
| Cable Diameter | Part No. | Use with Ferrule No. | Use with Screw No. | Use with Lag Eye No. | “D” Dia. | “E” Thread | “F” Dia. | “G” | “K” | “Ln” | “Lr” | “T” Thread |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1/8” | A-J62 | F-4 | SC-6 | LE-6 | .490” | 1/4-28 | .260” | .260” | .56” | .375” | 2.75” | 5/16-24 LH |
| 3/16” | A-J62 | F-6 | SC-6 | LE-6 | .490” | 1/4-28 | .260” | .260” | .56” | .375” | 2.75” | 5/16-24 LH |
| 1/4” | A-J82 | F-8 | SC-8 | LE-8 | .617” | 3/8-24 | .390” | .313” | .75” | .500” | 3.00” | 7/16-20 LH |
| 5/16” | A-J122 | F-10 | SC-8 | LE-8 | .744” | 3/8-24 | .390” | .348” | .87” | .620” | 4.50” | 9/16-18 |
| 3/8” | A-J122 | F-12 | SC-8 | LE-8 | .744” | 3/8-24 | .390” | .348” | .87” | .620” | 4.50” | 9/16-18 |
The Adjust-A-Jaw® is an exposed, swaged, tensioning,
face-of-the-post-mounted fitting that can be used on level or pitched runs. This fitting is available for 1/8”, 3/16”, 1/4”, 5/16”, and 3/8” diameter 1×19 stainless steel cable.
The Adjust-A-Jaw® can be used with any fitting on the opposite end of the run. This fitting attaches to the end post by installing a Threaded Tab into a pre-drilled and tapped hole in the end post and attaching the threaded jaw portion of the fitting to the threaded tab with a button head screw. The cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable. The lock nut is installed all the way onto the threaded jaw first, followed by the body, which is secured onto the jaw, creating tension on the cable. Once sufficient tension is achieved, the lock nut is secured against the end of the body to secure the fitting from loosening.
While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the threaded jaw portion of the fitting pivots at the tab. Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable. Ferrule sold separately.
Type 316 Stainless Steel
| Cable Diameter | Part No. |
Use with Ferrule No. |
Use with Screw No. | Use with Tab No. | “D” Dia. | “E” Thread | “F” Dia. | “G” | “K” | “Ln” | “Lr” | “T” Thread |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1/8” | A-J62 | F-4 | SC-6 | TT-6B | .490” | 1/4-28 | .260″ | .260″ | .56″ | .375″ | 2.75″ | 5/16-24 LH |
| 3/16” | A-J62 | F-6 | SC-6 | TT-6B | .490” | 1/4-28 | .260″ | .260″ | .56″ | .375″ | 2.75″ | 5/16-24 LH |
| 1/4” | A-J82 | F-8 | SC-8 | TT-8B | .617” | 3/8-24 | .390″ | .313″ | .75″ | .500″ | 3.00″ | 7/16-20 LH |
| 5/16” | A-J122 | F-10 | SC-8 | TT-8B | .744” | 3/8-24 | .390″ | .348″ | .87″ | .620″ | 4.50″ | 9/16-18 |
| 3/8” | A-J122 | F-12 | SC-8 | TT-8B | .744” | 3/8-24 | .390″ | .348″ | .87″ | .620″ | 4.50″ | 9/16-18 |
The Invisiware® Receiver with Invisiware® Stud combination is a concealed, swaged, tensioning, through-the-post-mounted fitting that is suitable for level runs. Receivers and studs are available for 1/8” and 3/16”, diameter 1×19 stainless steel cable; 1/8” and 3/16” sizes are also suitable for pitched applications.
The Invisiware® Receiver with Invisiware® Stud can be used with any other fitting on the opposite end of the run. This fitting is placed and concealed within a pre-drilled hole in the metal end post. The Receiver is furnished with a Delrin® washer that is installed between the shoulder of the fitting and the end post to protect the surface of the finish of the end post as tension is applied. The stud is swaged onto one end of the cable and is inserted and threaded into the Receiver installed in the end post. Tension is created by rotating the Receiver (with a hex wrench inserted into its broached end) and drawing the Stud into the Receiver.
This fitting in 1/8” and 3/16” cable sizes can also be used in pitched applications using the same method (including a horizontally drilled hole) described previously. This fitting is commonly paired with a Pull-Lock® on the opposite end of the run. The Receiver/Pull-Lock® terminal combination is available in our 1/8” and 3/16” kit offerings.
Invisiware® Receiver Dimensions
| Cable Diameter | 1/8″ Cable | 3/16″ Cable |
|---|---|---|
| Part Number | XR-6-XX | XR-6-XX |
| “D” Diameter | .437” | .437” |
| “T” Thread | 5/16-24 | 5/16-24 |
| “H” Hex | 3/16” | 3/16” |
| “S” Diameter | .537” | .537” |
| “L” Length | See “Framing Options” Table | |
Framing Options for Invisiware® Receiver
| Cable Diameter | 1/8″ Cable | 3/16″ Cable |
|---|---|---|
| Frame Options | Part No. | Part No. |
| 1-1/2″ Tube* or 1-1/4″ Pipe | XR-6-12 | XR-6-12 |
| 1-1/2″ Pipe | XR-6-22 | XR-6-22 |
| 2″x 2″ Tube | XR-6-32 | XR-6-32 |
| 2″ Pipe | XR-6-42 | XR-6-42 |
| 2-3/8″ Tube* | XR-6-72 | XR-6-72 |
| 2-1/2″ Tube* | XR-6-72 | XR-6-72 |
| 3″ Tube | XR-6-52 | XR-6-52 |
|
3-1/2″ Tube* |
XR-6-62 |
XR-6-62 |
*Round or Square Tube
The Clip-On Fixed Jaw is externally a duplicate of the Fixed Jaw and is only available for 1/8” and 3/16” diameter 1×19 stainless steel cable.
The Clip-On Fixed Jaw was created for applications that called for factory swaged fittings on both ends of the cable, without requiring over-sized holes through the intermediate posts (so an entire Fixed Jaw could pass through). This fitting accomplishes that with a .250” diameter ferrule that is pre-swaged to the cable. Once the cable with just a ferrule swaged to it is run through the intermediate posts to the end post to which it will attach, the jaw is slipped onto the cable over the ferrule and the clip installed at the ferrule. The jaw then slides back against the clip, which prevents the fitting from coming off the cable.
This fitting attaches to the wood end post by installing a Lag Eye into a pre-drilled hole in the end post and attaching the Clip-On Fixed Jaw to the lag eye with a button head screw. Lag eye and screw sold separately.
Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must also be purchased separately.
Type 316 Stainless Steel
| Cable Diameter | Part No. | Use with Ferrule No. | Use with Screw No. | Use with Lag Eye No. | “F” Dia. | “G” | “K” | “L” |
|---|---|---|---|---|---|---|---|---|
| 1/8” | F-JC2-4 | F-4 | SC-6 | LE-6 | .260” | .260” | .56” | 1.75” |
| 3/16” | F-JC2-6 | F-6 | SC-6 | LE-6 | .260” | .260” | .56” | 1.75” |
The Clip-On Fixed Jaw is externally a duplicate of the Fixed Jaw and is only available for 1/8” and 3/16” diameter 1×19 stainless steel cable.
The Clip-On Fixed Jaw was created for applications that called for factory swaged fittings on both ends of the cables, without requiring over-sized holes through the intermediate posts (so an entire Fixed Jaw could pass through). This fitting accomplishes that with a maximum diameter of a .250” diameter ferrule that is pre-swaged to the cable. Once the cable with only a ferrule swaged to it is run through the intermediate posts to the end post to which it will attach, the jaw is slipped onto the cable over the ferrule and the clip installed at the ferrule. The jaw then slides back against the clip, which prevents the fitting from coming off the cable.
This fitting attaches to the metal end post by installing a Threaded Tab into a pre-drilled and tapped hole in the end post and attaching the Clip-On Fixed Jaw to the threaded tab with a button head screw.
Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must also be purchased separately.
| Cable Diameter | Part No. | Use with Ferrule No. | Use with Screw No. | Use with Tab No. | “F” Dia. | “G” | “K” | “L” |
| 1/8” | F-JC2-4 | F-4 | SC-6 | TT-6B | .260” | .260” | .56” | 1.75” |
| 3/16” | F-JC2-6 | F-6 | SC-6 | TT-6B | .260” | .260” | .56” | 1.75” |
| Reference Fixed Jaw schematic to the right for call-outs. | ||||||||
The Fixed Jaw is an exposed, swaged, non-tensioning, face-of-the-post-mounted fitting that is suitable for use on level or pitched runs and is available for 1/8”, 3/16”, 1/4”, 5/16”, and 3/8” diameter 1×19 stainless steel cable.
The Fixed Jaw must be used with a tensioning fitting on the opposite end of the run. This fitting attaches to the wood end post by installing a Lag Eye into a pre-drilled hole in the end post and attaching the Fixed Jaw to the lag eye with a button head screw. The cable is retained within the Fixed Jaw by a ferrule swaged onto the end of the cable.
While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the Fixed Jaw pivots at the lag eye. The pre-drilled hole for the lag eye is drilled level, making installation easy.
Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must also be purchased separately. This fitting was designed to be compatible in appearance to the Adjust-A-Jaw® tensioning fitting.
Type 316 Stainless Steel
| Cable Diameter | Part No. | Use with Ferrule No. | Use with Screw No. | Use with Lag Eye No. | “E” Thread | “F” Dia. | “G” | “K” | “L” |
|---|---|---|---|---|---|---|---|---|---|
| 1/8” | F-J62 | F-4 | SC-6 | LE-6 | 1/4-28 | .260″ | .260″ | .56″ | 1.75″ |
| 3/16” | F-J62 | F-6 | SC-6 | LE-6 | 1/4-28 | .260″ | .260″ | .56″ | 1.75″ |
| 1/4” | F-J82 | F-8 | SC-8 | LE-8 | 3/8-24 | .390″ | .313″ | .75″ | 2.12″ |
| 5/16” | F-J122 | F-10 | SC-8 | LE-8 | 3/8-24 | .390″ | .348″ | .87″ | 2.25″ |
| 3/8” | F-J122 | F-12 | SC-8 | LE-8 | 3/8-24 | .390″ | .348″ | .87″ | 2.25″ |
Submit your info to receive updates from us!
Recent Comments