A convenient, easy-to-install means for attaching an Adjust-A-Body® with Threaded Eye, Adjust-A-Jaw®, Fixed Jaw, or Push-Lock® with Threaded Eye to a wood post.
Lag Eye with 1.5″ Thread
TYPE 316 STAINLESS STEEL
| Cable Diameter | Part No. | “G” | “H” | “T” | “S” | “L” | MIN NOMINAL TIMBER SIZE |
|---|---|---|---|---|---|---|---|
| 1/8” | LE-6 | .232″ | .735″ | .256″ | 1.50″ | 2.23″ | 4 X 4 |
| 3/16” | |||||||
| 1/4” | LE-8 | .290″ | 1.20″ | .393″ | 2.00″ | 3.55” | 4 X 4 |
| 5/16” | |||||||
| 3/8” |
Stainless steel steel socket-head screws for mounting an Adjust-A-Body® with Threaded Eye, Adjust-A-Jaw®, Fixed Jaw, or Push-Lock® with Threaded Eye.
Type 316 Stainless Steel
| Cable Diameter | Part No. | Thread |
|---|---|---|
| 1/8”, 3/16” | SC-6 | 1/4-28 |
| 1/4”, 5/16”, 3/8″ | SC-6 | 1/4-28 |
A strong finishing statement to your project.
The phosphor bronze cable is a contemporary color alternative to Ultra-tec’s cable offerings.
Cable Construction
1×19 strand cable is engineered to hold static loads without stretching, and it is relatively stiff. Other cable constructions are not offered in the bronze cable option because of their elevated levels of stretch and lower breaking strengths in comparison to 1×19 construction.
MINIMUM BREAKING STRENGTH (in lbs.)
FOR 1X19 STRAND TYPE 316 STAINLESS STEEL CABLE
| Cable Diameter | 1/8″ |
|---|---|
| Breaking Strength | 1, 780 |
| Cable Diameter | Breaking Strength | Part No. |
|---|---|---|
|
1/8” |
1,780 |
A4P |
To keep the cable from biting in the wood, the post protector tube is inserted into a wood post where the cable enters/exits the post at a angle.
| Cable Diameter | Tube Length | Part No. |
|---|---|---|
| 1/8”, 3/16” | 3/4″ | CS-TUBE |
The Pull-Lock® is a concealed, swageless, non-tensioning, through-the-post-mounted fitting that is suitable for use on level or pitched runs, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable.
The Pull-Lock® must be used with a tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled hole in the end post. Using the Pull-Lock® fitting on level or pitched runs requires that a minimum of 1-1/2” of clearance exists on the back side of the end post (to install the fitting and pull the cable through). It is also recommended that a stainless steel flat washer be installed between the shoulder of the fitting and the mating surface of the wood post (washer sold separately). The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.
You can use this fitting on a pitched application, using the same horizontally drilled method for 4×4 wood posts, by installing a post protector tube into the face of the post where the cable exits at an angle (the post protector tube protects the face of the post from abrasion and furrowing as the cable is tensioned). The post protector tube is sold separately.
This fitting is very much like the Push-Lock®, except the cable passes through the Pull-Lock®, meaning you can just cut the excess cable where it exits the fitting – no need to measure the cable before cutting. For that reason, it is the more popular of the two.
| Cable Diameter | Part No. |
|---|---|
| 1/8” | PUL-4-12 |
| 3/16” | PUL-6-12 |
The Push-Lock® is a concealed, swageless, non-tensioning, through-the-post-mounted fitting that is suitable for use on level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable.
The Push-Lock® must be used with a tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled hole in the end post. Using the Push-Lock® fitting on level runs requires that a minimum of 1-1/2” of clearance exists on the back side of the end post (to install the fitting through the back side of the post). It is also recommended that a stainless steel flat washer be installed between the shoulder of the fitting and the mating surface of the wood post. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.
This fitting is made to look similar to the Invisiware® Receiver from the exterior of the post, so it is recommended to use a Receiver with stud on the opposite end whenever practical to maintain a consistent look.
| Cable Diameter | Part No. |
|---|---|
| 1/8” | PL-4-12 |
| 3/16” | PL-6-12 |
The Push-Lock® Lag fitting is an exposed, swageless, non-tensioning, face-of-the-post-mounted fitting that is suitable for use on level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable.
The Push-Lock® Lag must be used with a tensioning fitting
on the opposite end of the run. This fitting is installed into a pre-drilled hole in the wood end post by rotating the fitting (with a wrench placed onto wrench flats machined into the fitting) to drive the lag thread into the hole until the fitting shoulders on the post face. Because the wrench flat is at the back of the fitting, it can be used with sleeved posts as well. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.
The most likely application for this fitting would be when substantial take-up is required, AND there is a preference for a swageless fitting, AND there is less than 2-1/2” of space available in back of the end post.
| Cable Diameter | Part No. |
|---|---|
| 1/8” | PL-LAG-4 |
| 3/16” | PL-LAG-6 |
The Push-Lock® Tensioner with Hanger Bolt is an exposed, swageless, tensioning, face-of-the-post-mounted fitting that is suitable for level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable. It is a more compact design than our swaged Adjust-A-Body® fittings.
The Push-Lock® Tensioner with Hanger Bolt can be used with any fitting on the opposite end of the run. This fitting consists of two separate pieces: the hanger bolt and Push-Lock® tensioning body. The hanger bolt is driven into a pre-drilled hole in face of the wood end post. The cable attaches to the body via our Push-Lock® locking wedge system which requires no special tools. The machine thread of the hanger bolt threads into the body, connecting the two pieces. Tension is created by securing the post-side segment of the body onto the machine threads while preventing the cable-side segment of the body from turning. The Push-Lock® Tensioner with Hanger Bolt can be used with sleeved posts as well.
We do not recommend this fitting being installed in pitched applications because it would require drilling all of the holes in the end post at an angle. While this is possible with special fixtures, if it is not done correctly the end result would be visually unacceptable.
| Cable Diameter | Part No. |
|---|---|
| 1/8” | PL-SFC-WS-4 |
| 3/16” | PL-SFC-WS-6 |
The Push-Lock® Tensioner with Lag Clevis is an exposed, swageless, tensioning, face-of-the-post-mounted fitting that is suitable for level or pitched runs, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable. It is a more compact design than our swaged Adjust-A-Body® fittings.
The Push-Lock® Tensioner with Lag Clevis can be used with any fitting on the opposite end of the run. This fitting consists of two separate pieces: the articulating lag and the Push-Lock® tensioning body. The lag is driven into a pre-drilled hole in the wood end post. The cable attaches to the body via our Push-Lock® locking wedge system which requires no special tools. The machine thread of the articulating lag threads into the body, connecting the two pieces. Tension is created by securing the post-side segment of the body onto the machine threads while preventing the cable-side segment of the body from turning.
While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the threaded eye portion of the fitting pivots at the lag. The pre-drilled hole for the lag is drilled level, making installation easy.
| Cable Diameter | Part No. |
|---|---|
| 1/8” | PL-SFC-WP-4-1 |
| 3/16” | PL-SFC-WP-6-1 |
The Push-Lock® with Lag Clevis is an exposed, swageless, non-tensioning, face-of-the-post-mounted fitting that is suitable for level or pitched runs, and is available for1/8” and 3/16” diameter 1×19 stainless steel cable.
The Push-Lock® with Lag Clevis can be used with any tensioning fitting on the opposite end of the run. This fitting is installed into a pre-drilled hole in the wood end post. Drive the lag thread into the hole until the fitting shoulders on the post face. The cable attaches to the body via our Push-Lock® locking wedge system which requires no special tools.
While this fitting can be used on pitched or level runs, it is most appropriate for pitched runs because the body of the fitting pivots at the clevis. The pre-drilled hole for the lag eye is drilled level, making installation easy.
| Cable Diameter | Part No. |
|---|---|
| 1/8” | PL-LAG-CL-TE4-1 |
| 3/16” | PL-LAG-CL-TE6-1 |
Submit your info to receive updates from us!
Recent Comments