FOLLOW US

Post Type: Sleeved

This fitting is identical to the Adjust-a-Body® with Hanger Bolt except the extended length hanger bolt is 3” long. Designed to reach past sleeves and drywall to find the wood post or frame underneath. It is used for sleeved posts with an outside diameter of greater than 4-1/2”. 


Use of this fitting requires an appropriately sized ferrule that is swaged onto the cable, which must be purchased separately.

Specifications

Cable Diameter Part No.  Use With Ferrule No. 
1/8”

A-JB6-L

 F-4
3/16” F-6

ADJUST-A-BODY eXTENDED LENGTH LAG WITH THREADED EYE

For sleeved posts with an outside diameter of greater than 4-1/2”, use the extended length lag eye. The extended length lag is 3” long, designed to reach past sleeves and drywall to find the wood post or frame underneath.

Extended lag eye and screw sold separately.

Specifications

Type 316 Stainless Steel

Cable Diameter Part No.  Use Ferrule No. Use With Screw No. Use With Extended Length Lag Eye “E” Thread “A” “B” “S” “T” Thread “Lt” “Ln” “Lr” “D” Dia. 
1/8” A-JTE6 F-4 SC-6 LE-6L 1/4-28 .233″/.229″ .500″ .44″ 5/16-24 LH 2.00″ .375″ 2.75″ .490″
3/16” A-JTE6 F-6 SC-6 LE-6L 1/4-28 .233″/.229″ .500″ .44″ 5/16-24 LH 2.00″ .375″ 2.75″ .490″

Adjust-A-Body® with Extended Length Lag for Composite Sleeved Posts

Exposed, swaged, tensioning, face-of-the-post-mounted fitting suitable for level or pitched runs and is available for 1/8˝ and 3/16˝ diameter 1×19 stainless steel cable.

  • Can be used with any fitting on the opposite end of the run.
  • Consists of two separate pieces: the articulating Lag Bolt and Adjust-a-Body® tensioning body.
  • Threaded Clevis is installed into a pre-drilled or tapped hole in the end post.
    Cable is retained within the body portion of the fitting by a ferrule swaged onto the end of the cable.
  • Use of this fitting requires an appropriate sized ferrule that is swaged onto the cable, which much be purchased separately.
  • Once sufficient tension is achieved, the Lock Nut is secured against the end of the body to secure the fitting from loosening.

Part Number: A-J6-CL-C

A-J6-CL-C
A-J6-CL-C
A-J6-CL-C-2

Specifications

Cable Diameter Use with Ferrule No.  “T” Thread “Lt” “Ln” “Lr” “D” Dia.
1/8” F-4 6/16-24 LH 2.00″ .375″ 2.73″ .490″
3/16” F-6

CONCEALED TENSIONING FITTING​

The Invisiware® Receiver with Invisiware® Stud combination is a concealed, swaged, tensioning, through-the-post-mounted fitting that is suitable for level runs. Receivers and studs are available for 1/8” and 3/16”,  diameter 1×19 stainless steel cable; 1/8” and 3/16” sizes are also suitable for pitched applications.

The Invisiware® Receiver with Invisiware® Stud can be used with any other fitting on the opposite end of the run. This fitting is placed and concealed within a pre-drilled hole in the metal end post. The Receiver is furnished with a Delrin® washer that is installed between the shoulder of the fitting and the end post to protect the surface of the finish of the end post as tension is applied. The stud is swaged onto one end of the cable and is inserted and threaded into the Receiver installed in the end post. Tension is created by rotating the Receiver (with a hex wrench inserted into its broached end) and drawing the Stud into the Receiver.

This fitting in 1/8” and 3/16” cable sizes can also be used in pitched applications using the same method (including a horizontally drilled hole) described previously. This fitting is commonly paired with a Pull-Lock® on the opposite end of the run. The Receiver/Pull-Lock® terminal combination is available in our 1/8” and 3/16” kit offerings.

bronze reciever
tall bronze reciever

Specifications

Invisiware® Receiver Dimensions

Cable Diameter 1/8″ Cable 3/16″ Cable
Part Number  XR-6-XX XR-6-XX
“D” Diameter .437” .437”
“T” Thread 5/16-24 5/16-24
“H” Hex 3/16” 3/16”
“S” Diameter .537” .537”
“L” Length See “Framing Options” Table

Framing Options for Invisiware® Receiver

Cable Diameter 1/8″ Cable 3/16″ Cable
Frame Options Part No.  Part No. 
1-1/2″ Tube* or 1-1/4″ Pipe XR-6-12 XR-6-12
1-1/2″ Pipe XR-6-22 XR-6-22
2″x 2″ Tube XR-6-32 XR-6-32
2″ Pipe XR-6-42 XR-6-42
2-3/8″ Tube* XR-6-72 XR-6-72
2-1/2″ Tube* XR-6-72 XR-6-72
3″ Tube XR-6-52 XR-6-52

3-1/2″ Tube*

 XR-6-62

XR-6-62

*Round or Square Tube

A convenient, easy-to-install means for attaching an Adjust-A-Body® with Threaded Eye, Adjust-A-Jaw®, Fixed Jaw, or Push-Lock® with Threaded Eye  to a sleeved post.

Specifications

Extended Length Lag Eye with 3-inch  Thread

Type 316 Stainless Steel 

Cable Diameter Part No. Tube Length Tube Length Tube Length Tube Length Tube Length Part No.
1/8” LE-6L .232” .780” .256″ 3.00″ 3.94″ 4 X 4
3/16”

The ferrule is used to retain an Adjust-A-Jaw®,
Adjust-A-Body® or a Fixed Jaw onto cable.

Specifications

Cable Diameter Part No . After Swaged “D” Dia. After Swaged “L” Length 
1/8” F-4 .250″ .61″
3/16” F-6 .250″ .56″
3/4” F-8 .375″ .70″
5/16″ F-10 .500″ .73″
3/8″ F-12 .500″ .71″

A convenient, easy-to-install means for attaching an Adjust-A-Body® with Threaded Eye, Adjust-A-Jaw®, Fixed Jaw, or Push-Lock® with Threaded Eye to a wood post.

Specifications

Lag Eye with 1.5″ Thread

TYPE 316 STAINLESS STEEL

Cable Diameter Part No. “G” “H” “T” “S” “L” MIN NOMINAL TIMBER SIZE
1/8” LE-6 .232″ .735″ .256″ 1.50″ 2.23″ 4 X 4
3/16”
1/4” LE-8 .290″ 1.20″ .393″ 2.00″ 3.55” 4 X 4
5/16”
3/8”

mounting screw for lag eye fittings

Stainless steel steel socket-head screws for mounting an Adjust-A-Body® with Threaded Eye, Adjust-A-Jaw®, Fixed Jaw, or Push-Lock® with Threaded Eye.

Specifications

Type 316 Stainless Steel

Cable Diameter Part No. Thread
1/8”, 3/16” SC-6 1/4-28
1/4”, 5/16”, 3/8″ SC-6 1/4-28

Phosphor Bronze Cable:
1/8" Diameter, 1X19

A strong finishing statement to your project.

The phosphor bronze cable is a contemporary color alternative to Ultra-tec’s cable offerings. 

  • Designed as a 1/8″ diameter cable.
  • Corrosion Resistant.
  • 1×19 strand cable engineered to hold static loads without stretching and is relatively stiff.

 

Cable Construction 

 1×19 strand cable is engineered to hold static loads without stretching, and it is relatively stiff. Other cable constructions are not offered in the bronze cable option because of their elevated levels of stretch and lower breaking strengths in comparison to 1×19 construction.

 

MINIMUM BREAKING STRENGTH (in lbs.)

FOR 1X19 STRAND TYPE 316 STAINLESS STEEL CABLE

 

Cable Diameter 1/8″
Breaking Strength 1, 780

 

 

Specifications

Cable Diameter Breaking Strength Part No.

1/8”

1,780

 A4P

The Push-Lock® Lag fitting is an exposed, swageless, non-tensioning, face-of-the-post-mounted fitting that is suitable for use on level runs only, and is available for 1/8” and 3/16” diameter 1×19 stainless steel cable.


The Push-Lock® Lag must be used with a tensioning fitting
on the opposite end of the run. This fitting is installed into a pre-drilled hole in the wood end post by rotating the fitting (with a wrench placed onto wrench flats machined into the fitting) to drive the lag thread into the hole until the fitting shoulders on the post face. Because the wrench flat is at the back of the fitting, it can be used with sleeved posts as well. The cable attaches to the fitting via our Push-Lock® locking wedge system which requires no special tools.


The most likely application for this fitting would be when substantial take-up is required, AND there is a preference for a swageless fitting, AND there is less than 2-1/2” of space available in back of the end post.

Specifications

Cable Diameter Part No.
1/8” PL-LAG-4
3/16” PL-LAG-6

SITESEARCH

WHERETO BUY